CWAP-404 Dumps with Practice Exam Questions Answers

A hexadecimal value is a value that uses base 16 notation, which means it can have digits from 0 to 9 and letters from A to F. A hexadecimal value is usually preceded by 0x to indicate that it is hexadecimal and not decimal or binary. For example, 0x0A is hexadecimal for 10 in decimal or 00001010 in binary. The other options are not valid prefixes for hexadecimal values.References:

• CWAP-404 Study Guide, Chapter 2: Protocol Analysis, page 35
• CWAP-404 Objectives, Section 2.2: Analyze field values

The default 802.11 authentication method for a STA when using Pre-RSNA is Open System. This is the simplest and most common authentication method, which does not provide any security or encryption. In Open System authentication, the STA sends an Authentication Request frame to the AP, and the AP responds with an Authentication Response frame with a status code of success. After this, the STA can proceed to association with the AP . References: CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 181; CWAP-404 Certified Wireless Analysis Professional Study and Reference Guide, Chapter 6: MAC Sublayer Frame Exchanges, page 183.

The CRC is calculated over the MAC Header and Frame Body only. The CRC (Cyclic Redundancy Check) is a 32-bit value that is used for error detection in wireless transmissions. The CRC is calculated over the MAC Header and Frame Body of a PSDU, which are the parts of the data unit that contain information such as source and destination addresses, frame type, frame control, sequence number, payload, etc. The CRC is appended to the end of the PSDU as a FCS (Frame Check Sequence) field. The CRC is not calculated over the PHY Header or PHY Preamble, which are parts of the PPDU that contain information such as modulation, coding, data rate, etc. The PHY Header and PHY Preamble are added or removed by the PHY layer during the conversion between PSDU and PPDU. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 97-98

A capture visualization tool is a software application that can open a packet capture file and display various graphs, charts, tables, and statistics that illustrate the characteristics and behavior of the wireless network. A capture visualization tool can help a network administrator with little knowledge of 802.11 protocols to evaluate the overall health and performance of their wireless network by providing a visual and intuitive representation of the captured data. A spectrum analyzer is a hardware device that measures the radio frequency signals in a given frequency range and displays their amplitude, frequency, and modulation. A spectrum analyzer can help identify sources of interference and noise in the wireless environment, but it cannot open a packet capture file. Python is a programming language that can be used to write scripts or applications that manipulate or analyze packet capture files, but it requires coding skills and knowledge of 802.11 protocols. A WLAN scanner is a software application that scans for available wireless networks and displays information such as SSID, BSSID, channel, signal strength, security type, and vendor. A WLAN scanner can help discover wireless networks and their basic parameters, but it cannot open a packet capture file345 References:

• CWAP-404 Study Guide, Chapter 2: Protocol Analysis, page 63
• CWAP-404 Objectives, Section 2.5: Use capture visualization tools
• CWAP-404 Study Guide, Chapter 4: Spectrum Analysis and Troubleshooting, page 117
• CWAP-404 Objectives, Section 4.1: Use spectrum analysis tools
• CWAP-404 Study Guide, Chapter 2: Protocol Analysis, page 33
• CWAP-404 Objectives, Section 2.2: Analyze field values

Delta is the timing column in the packet view that measures the time difference between two consecutive packets in a capture file. Delta can be used to measure the roaming time from the last VoIP packet sent on the old AP’s channel to the first VoIP packet sent on the new AP’s channel by selecting these two packets and looking at their delta values. The other timing columns are not suitable for this measurement because they do not show the time difference between two specific packets. Roaming is a column that shows whether a packet belongs to a roaming event or not. Relative is a column that shows the time elapsed since the beginning of the capture file. Absolute is a column that shows the date and time when a packet was captured5 References:

• CWAP-404 Study Guide, Chapter 2: Protocol Analysis, page 57
• CWAP-404 Objectives, Section 2.4: Analyze timing values