Activate Your Black Friday Offer: 75% Discount on Exam Bundles! Use coupon code below! - Ends in 0d 00h 00m 00s - Coupon code: 75onlydt

H12-323_V2.0 Questions and Answers

Question # 6

A VLAN pool can be configured to supply service VLANs. Which of the following statements about a VLAN pool is false?

A.

If the VLAN assignment algorithm is set to hash and a STA goes online multiple times, the STA is preferentially assigned the IP addresses it uses previously.

B.

Configuring a VLAN pool to provide service VLANs can reduce the number of STAs in each VLAN and also the size of the broadcast domain.

C.

If the VLAN assignment algorithm is set to even and a STA goes online multiple times, the STA obtains different IP addresses each time.

D.

Nonexistent VLANs cannot be added to a VLAN pool.

Full Access
Question # 7

Which WAC reliability networking modes require the active and standby WACs to use the same models and software versions?

CHOOSE TWO

A.

Dual-link HSB

B.

Dual-link cold backup

C.

VRRP HSB

D.

N+1 backup

Full Access
Question # 8

Actual packet transmission rates of STAs differ greatly depending on the radio modes that STAs support and the radio environment. The airtime scheduling function allocates channel resources according to the channel-occupation time of users connected to the same radio. Each user receives equal time to occupy the channel, ensuring fairness in channel occupation. If multiple users send different packet types, airtime scheduling still takes effect.

A.

TRUE

B.

FALSE

Full Access
Question # 9

In roaming scenarios, because of individual differences, some STAs do not roam to APs with stronger signals and instead remain connected to the initially associated APs, even if they are disconnected. These STAs might not initiate association requests again after disconnection. To resolve this problem, the WAC directly takes these sticky STAs offline.

A.

TRUE

B.

FALSE

Full Access
Question # 10

During AP installation and deployment, APs may use Ethernet cables for PoE power. Which of the following statements about the PoE protocol are true?

CHOOSE All that Apply

A.

The maximum output power of a device supporting PoE+ is 30 W.

B.

PoE++ technology complies with IEEE 802.3bt.

C.

The maximum output power of a device supporting PoE is 15.4 W.

D.

The maximum output power of a device supporting PoE++ is 60 W.

Full Access
Question # 11

In classroom settings, indoor floor height is generally about 3 m to 5 m. The following figure presents WLAN planning solutions for typical classrooms and lecture halls. Match the recommended antenna types and installation modes to the two solutions.

Question # 11

Question # 11

Full Access
Question # 12

The CloudCampus APP’s AP calculator incorporates a variety of scenarios and network-construction standards. Which of the following scenarios is not included?

A.

Mine

B.

High-density stadium

C.

Hotel

D.

Shopping mall

Full Access
Question # 13

On an agile distributed WLAN, RUs and central APs must be located on the same Layer 2 network, and each RU can associate with only one central AP.

A.

TRUE

B.

FALSE

Full Access
Question # 14

What is the maximum number of spatial streams that a 3x2 MIMO WLAN system supports?

A.

2

B.

3

C.

5

D.

6

Full Access
Question # 15

Which of the following statements are correct regarding network optimization in the WLAN optimization solution?

CHOOSE THREE

A.

The AP management VLAN and service VLAN cannot be set to VLAN 1 to prevent loops.

B.

As there are a large number of APs, different service VLANs can be used when different SSIDs are configured.

C.

It is recommended that AP/WAC management addresses be separated from user service addresses to facilitate management and control.

D.

In scenarios where users move frequently, it is recommended that the lease of the address pool be shortened so that IP addresses can be reclaimed in a timely manner.

Full Access
Question # 16

Some STAs cannot access a WLAN because of coverage holes. In this situation, the transmit-power values of neighboring APs can be adjusted to enlarge the coverage area and eliminate the holes. Which command sequence is used to manually adjust AP transmit power?

Question # 16

Original exhibit: Q53 Enlarged Exhibit

A.

Option A

B.

Option B

C.

Option C

D.

Option D

Full Access