Special Limited Time 65% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: dpt65

E20-375 Questions and Answers

Question # 6

An environment consists of a two-RPA, single cluster. There are 112 Consistency Groups (CGs) configured and replicating. The administrator asks you what impact an RPA failure would have.

What should you tell them?

A.

All CGs will run on a single RPA.

B.

The first 64 CGs will run on the single RPA, the others will be disabled.

C.

The first 64 CGs will run on the single RPA, the others will be paused.

D.

The 64 CGs with the highest priority will run on the single RPA.

Full Access
Question # 7

You are working on a RecoverPoint local replication solution in an environment that includes VNX and VMAX storage arrays. You want to create a Consistency Group (CG) for your Oracle database. However, some of the database volumes are located in the VNX and others are located in the VMAX.

What is the recommended management solution?

A.

Create one CG using VNX and VMAX volumes

B.

Create a new RecoverPoint cluster and add the VNX splitter

C.

Migrate all LUNs to the VMAX

D.

Create two CGs: one for VNX volumes and another for VMAX volumes

Full Access
Question # 8

A conversion from RecoverPoint/SE to RecoverPoint/EX was just completed. What is the next required step?

A.

Remove RecoverPoint/SE license, then add RecoverPoint/EX license

B.

Add RecoverPoint/EX license directly, because the newly added license will replace the existing one

C.

Run a health check of RecoverPoint/EX

D.

Reconfigure the Consistency Groups

Full Access
Question # 9

What is a quick way to determine if the required TCP ports for RecoverPoint are blocked?

A.

Run the Ports Diagnostics test by connecting to an RPA as the boxmgmt user

B.

Browse to the site management address and open Unisphere for RecoverPoint

C.

Run the Port Diagnostics test by connecting to an RPA as the admin user

D.

Run the Port Diagnostics test by connecting to an RPA as the security-admin user

Full Access
Question # 10

RecoverPoint support has asked you to collect logs from your RecoverPoint system. After the log collection process is complete, which user account is used to access the log file for download?

A.

admin

B.

webdownload

C.

boxmgmt

D.

security-admin

Full Access
Question # 11

After running a log collection, which user should you log in as to download the output file?

A.

admin

B.

monitor

C.

boxmgmt

D.

security-admin

Full Access
Question # 12

What is a benefit of integrating RecoverPoint with VMware Site Recovery Manager (SRM)?

A.

Enables coordinated failover of virtual machines and their storage

B.

Eliminates hardware dependencies when using heterogeneous storage with VMware

C.

Enables replication of individual virtual machines without the need to replicate an entire VMFS volume

D.

Enables full protection of VMware ESXi servers

Full Access
Question # 13

What should be used when more performance is needed than a single RPA can provide for asynchronous replication?

A.

Distributed Consistency Groups

B.

Journal Compression

C.

Fibre Channel connections

D.

Multi-Cluster copies

Full Access
Question # 14

A customer is installing a new RecoverPoint environment. All RPAs have been racked, cabled, and powered on. You have chosen to automatically discover the RPAs using Deployment Manager. After running the discovery, no RPAs are found.

What is the most likely cause of this issue?

A.

No DHCP server on the network

B.

Port 443 not open on the network

C.

RecoverPoint/SE wizard selected

D.

RPAs not configured into a cluster

Full Access
Question # 15

Through what does RecoverPoint support heterogeneous storage environments?

A.

VPLEX

B.

Any array-based splitter

C.

APIs

D.

VMAX splitter only

Full Access
Question # 16

What is the maximum number of copies supported using the MetroPoint topology for VPLEX continuous data replication?

A.

3

B.

4

C.

5

D.

8

Full Access
Question # 17

Which statement is true regarding vRPAs?

A.

vRPAs are deployed using the OVA template.

B.

The proper license must be installed before vRPA deployment.

C.

vRPAs can be connected to storage through the VNX splitter in the RecoverPoint/SE system.

D.

vRPAs are installed using Unisphere for RecoverPoint.

Full Access
Question # 18

What action causes the loss of journal content?

A.

The replica is accessed in Direct Access mode

B.

Enabling Image Access mode

C.

A journal is added to a Consistency Group

D.

An RPA performed marking

Full Access
Question # 19

A company has a DR site connected using a 4 Gbps FC link and two RPAs on the primary site, and two RPAs at the DR site. They are experiencing high load events although the FC link is not fully utilized.

What would be the best solution to get the FC link utilization up as high as possible?

A.

Add two RPAs to the primary site and add two RPAs to the DR site

B.

Add two RPAs to the primary site only

C.

Use distributed consistency groups with one primary RPA and two secondary RPAs on the primary site

D.

Add two RPAs to the DR site only

Full Access
Question # 20

Which image access mode provides the quickest way to access data?

A.

Virtual Access

B.

Logged Access

C.

Direct Access

D.

Snap Access

Full Access
Question # 21

You are deploying a RecoverPoint cluster into an existing VPLEX environment. You want to validate the following conditions:

  • VPLEX splitters are installed
  • All VPLEX splitters are the same version
  • VPLEX splitter status

In addition, you want to verify that the VPLEX management server can reach all of the attached RecoverPoint clusters.

How can you verify all the information?

A.

Use VPLEX CLI to run rp validate-configuration

B.

Use VPLEX CLI to run rp verify-configuration

C.

Use RecoverPoint CLI to run rp validate-configuration

D.

Use RecoverPoint CLI to run rp verify-configuration

Full Access
Question # 22

A storage administrator is installing the VSI RecoverPoint Management plug-in, but the installation fails.

What could be causing this?

A.

vSphere client not installed

B.

vSphere client not running during the installation

C.

RPAs used were all virtual

D.

At least one virtual RPA present

Full Access
Question # 23

What is a possible trigger to initiate RecoverPoint Snap-based Replication?

A.

High Load condition detected

B.

RecoverPoint snapshot takes place

C.

INIT snapshot takes place

D.

Incoming date marked on Delta Marker stream

Full Access
Question # 24

During a failover event, you have determined that the last bookmark had corrupted data. What is the fastest way to find the last good replica?

A.

Fail back to the primary and create a new replica

B.

Complete the failover and restore the data from the local backup

C.

Create a new bookmark and use the Test a Copy wizard

D.

Move to the previous point in time

Full Access
Question # 25

A company with a DR site connected with a 2 Gbps FC link has three RPAs at each site. They are experiencing High Load events, although the FC link is not fully utilized.

What would be the best solution to get the FC link utilization up as high as possible while mitigating those events?

A.

Use a Distributed Consistency Group

B.

Add one RPA to the Primary site

C.

Use the Consistency Group on both RPAs and add two RPAs to the secondary site

D.

Add one RPA to the DR site

Full Access
Question # 26

A VMware user is currently protecting their virtual application servers with RecoverPoint. All data is stored on two VNX arrays. They will soon be adding Site Recovery Manager (SRM) to their VMware infrastructure.

What will be needed to integrate RecoverPoint functionality into their SRM deployment?

A.

EMC Storage Replication Adapter (SRA) for RecoverPoint only

B.

EMC Virtual Storage Integrator (VSI)

C.

EMC Storage Replication Adapters (SRAs) for VNX and RecoverPoint

D.

vSphere SRM Plug-in for Unisphere for RecoverPoint

Full Access
Question # 27

Which RecoverPoint tool will give you an overview of the system state, based on the system’s long term statistics?

A.

Detect Bottlenecks

B.

Balance Load

C.

Collect System Information

D.

Manage Event Filters

Full Access
Question # 28

Once a device is in an Open Replicator RecoverPoint session, what must be done in order to make configuration changes to that device?

A.

Disable the Configuration Group

B.

Pause the Configuration Group

C.

Unmap the device

D.

Unmask the device

Full Access
Question # 29

You are a storage administrator tasked with creating a Consistency Group in a RecoverPoint/EX system. You launch the Protect Volumes wizard in Unisphere and notice that the desired production volume is not available.

What would be a possible cause?

A.

The production volumes are on a non-licensed array.

B.

The volumes are masked to a host.

C.

The journal volumes are on a non-licensed array.

D.

Consistency Groups can only be created by boxmgmt.

Full Access
Question # 30

A customer has added VPLEX to an existing RecoverPoint system. When configuring journals for a new Consistency Group they note that VPLEX Distributed Volumes are available.

Why are Distributed Volumes available?

A.

Certificates were not created when installing the VPLEX splitter.

B.

This is not a problem; you can tell the customer to use them.

C.

The VPLEX is not running GeoSynchrony code 5.1.

D.

The VPLEX Distributed Volume should not be in the RPA Storage View.

Full Access