NS0-077 Dumps with Practice Exam Questions Answers

FabricPool normally connects ONTAP to StorageGRID through an HTTPS load balancer endpoint. That endpoint uses a server certificate so that ONTAP can authenticate the StorageGRID service. NetApp specifically warns that if the certificate securing the ONTAP-to-StorageGRID connection expires, FabricPool temporarily stops working and ONTAP loses access to data tiered to StorageGRID.

The same problem can occur when the endpoint certificate is renewed or replaced in StorageGRID but the corresponding trusted certificate on ONTAP is not updated. NetApp requires the StorageGRID and ONTAP certificate configurations to remain synchronized; after certificate replacement or renewal, ONTAP must trust the new certificate chain.

The scenario also eliminates the node-failure answers. The two Gateway Nodes are configured in an HA group, so failure of one Gateway Node should not independently cause the FabricPool endpoint to become unavailable. Likewise, losing one Storage Node does not normally prevent access to the StorageGRID S3 service. A Client Network trust-state change would have broader networking implications and does not fit the isolated, time-related FabricPool failure described.

Therefore, C is the correct answer.

Reference topics: FabricPool Integration → StorageGRID Load Balancer Endpoints → HTTPS/TLS Certificates → Certificate Expiration and Rotation

Adding another SG1100 services appliance increases aggregate client throughput because each SG1100 can operate as a Gateway Node running the StorageGRID Load Balancer service. With DNS Round Robin, client connections are distributed across the available services appliances, allowing the aggregate load-balancing capacity to scale horizontally. NetApp explicitly identifies increased aggregate throughput and no idle hosts as advantages of the DNS Round Robin load-balancing model.

The SG1100 is specifically designed to provide high-performance Gateway Node and Admin Node services and supports high-speed network connectivity up to 100 GbE. Adding another equivalent SG1100 therefore provides additional processing and network capacity while preserving consistent performance characteristics across the load-balancer pool. NetApp cautions against mixing services appliances with substantially different performance levels when balancing client traffic.

Option B is incorrect because the SGF6112 is a Storage Node appliance, while StorageGRID load-balancer caching is available only on Gateway Nodes. Option C does not provide the same intended horizontal client-throughput expansion. Option D would substitute an SG110, a lower-performance services appliance, and could create inconsistent load-balancing performance.

Therefore, A is the correct answer.

Reference topics: StorageGRID Load Balancing → DNS Round Robin → SG1100 Services Appliances → Gateway Nodes → Aggregate Client Throughput

The correct configuration is to route StorageGRID AutoSupport traffic through an Admin proxy server. NetApp states that when AutoSupport packages are transmitted using HTTPS, the primary Admin Node requires outbound access to NetApp Technical Support either directly or through a proxy server. This is specifically intended for secure environments where StorageGRID nodes cannot establish unrestricted direct internet connections.

The administrator configures this under Configuration > Security > Proxy settings > Admin, enables the Admin proxy, and specifies the proxy server hostname or IP address and port. Authentication credentials can also be supplied when required. Once configured, AutoSupport traffic from Admin Nodes to NetApp Technical Support is routed through this controlled proxy path.

This preserves normal AutoSupport functionality, including periodic and event-triggered AutoSupport packages, which support proactive monitoring and automatic support-case workflows. Manually uploading bundles, as in A, would not provide the desired automated behavior. Option B does not solve the connectivity restriction. Option C is also incorrect because AutoSupport On Demand is intended primarily for active troubleshooting and itself requires HTTPS connectivity; it does not replace normal automated AutoSupport delivery.

Therefore, D provides the required secure outbound connectivity while retaining automated NetApp support capabilities.

Reference topics: Grid Manager → AutoSupport → Admin Proxy → HTTPS AutoSupport → Event-Triggered AutoSupport → NetApp Technical Support Connectivity

NetApp defines a specific workflow for migrating a Linux-based StorageGRID node between hosts. The source node must first be shut down cleanly using storagegrid node stop. After the node has stopped, the administrator runs storagegrid node export on the source host. The export output identifies the /var/local storage volume and provides the corresponding import command to use on the target host.

On Host-B, the administrator runs storagegrid node import against the exported node storage. NetApp then requires the imported configuration to be checked with storagegrid node validate. After successful validation, the migrated node is started with storagegrid node start, and Grid Manager is used to confirm that the node returns to a green operational state with no alerts.

Therefore, C represents the required migration sequence. Although the option summarizes the final validation/start phase, its stop → export → import → verify ordering matches NetApp's prescribed procedure.

Option A is incorrect because Grid Manager does not automatically migrate Linux containers. Option B reverses the export/import sequence. Option D incorrectly treats migration as a new StorageGRID installation and node reconfiguration.

Reference topics: StorageGRID Maintenance → Linux Host Migration → Node Stop → Node Export → Node Import → Validate → Start → Grid Manager Verification

When a physical or virtual host containing multiple StorageGRID nodes fails, NetApp defines a specific recovery-order requirement when one of those nodes is the primary Admin Node. StorageGRID 12.0 documentation states that if the failed server hosts the primary Admin Node, the primary Admin Node must be recovered first. This prevents subsequent node-recovery operations from stopping while attempting to communicate with services associated with the primary Admin Node.

Therefore, the administrator should deploy a replacement VM for the primary Admin Node and perform the documented primary Admin Node recovery. After the primary Admin Node is operational, recovery of the failed Gateway Node can proceed, restoring the intended client load-balancing path.

Option A is invalid because StorageGRID does not permit adding a primary Admin Node through an expansion; the primary Admin Node is established during initial installation and a failed one must be recovered. Options B and D incorrectly prioritize the Gateway Node while the failed host also contains the primary Admin Node. The StorageGRID 12.0 recovery guidance explicitly requires the primary Admin Node to be handled first in this situation.

Reference topics: Maintenance → Node Recovery → Primary Admin Node Recovery → Multiple Nodes on Failed Host → Gateway Node Recovery → Load Balancer Service