Special Limited Time 65% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: dpt65

DES-6321 Questions and Answers

Question # 6

What are all of the menu option choices available in the RASR factory reset procedure when booting from the RASR ISO?

A.

RASR RESET

CREATE RASRUSB

FACTORY RESET

QUIT

B.

RASR RESET

CREATE RASRUSB

FACTORY RESET

REBOOT

UPDATE FIRMWARE

QUIT

C.

RASR RESET

CREATE RASRUSB

FACTORY RESET

UPDATE FIRMWARE

EXIT

D.

RASR RESET

CREATE RASRUSB

FACTORY RESET

REBOOT

UPDATE FIRMWARE

EXIT

Full Access
Question # 7

Where is the VxRail Manager pre-installed on a newly shipped, 4 node VxRail Model G410 system?

A.

Node with the highest serial number

B.

Bottom-right node from the front

C.

All nodes

D.

First node

Full Access
Question # 8

A VxRail Stretched Cluster deployment will have E560F node. The Cluster must allow local protection with both erasure coding options at either site.

What is the minimum node configuration/

A.

3+3 nodes

B.

4+4 nodes

C.

6+6 nodes

D.

8+8 nodes

Full Access
Question # 9

Which block of IP addresses that is provided by the user to the VxRail Initialization wizard may contain noncontiguous

addresses?

A.

NTP Servers

B.

ESXi Host

C.

vSAN

D.

vSphere vMotion

Full Access
Question # 10

A VxRail Cluster setup with P570F nodes is used for product evaluation purposes at customer sites. Before moving the Cluster to another customer site, it needs to be reset

Where is the image located to complete this task?

A.

SATADOM

B.

IDSDM

C.

BOSS

D.

MB Server

Full Access
Question # 11

What statement accurately describes the tail types used in racking VxRail nodes?

A.

Static rails only support the option to use a cable management arm (CMA)

B.

Sliding rails are available on all models of Dell 14G VxRail nodes except for the S570

C.

Static rails enable the VxRail nodes to be fully extended out of the rack for service

D.

Sliding rails are available on all models of Dell 14G VxRail nodes except for the G560

Full Access
Question # 12

You are performing a troubleshooting steps on a 4 node VxRail cluster. The cluster uses Erasure Coding for all VMs. When you attempt to put a node into maintenance mode using the recommended vSAN data

migration policy, the operation fails.

What could be done to successfully put the node into maintenance mode?

A.

Use the ‘No Data Migration’ option

B.

Storage vMotion the VMs off the node

C.

Cold migrate the VMs off the node

D.

Use the ‘Full Data Migration’ option

Full Access
Question # 13

You are in the validation phase of a VxRail deployment with two Top of Rack (ToR) switches and four V570F VxRail nodes.

Which command should you issue on each of the ToR switches to validate that Link Aggregation has not been configured for VxRail interfaces?

A.

show spanning tree

B.

show interfaces port-channel brief

C.

show vlan

D.

show running config mld

Full Access
Question # 14

What VxRail model is designed to support graphic intensive VDI workloads?

A.

E Series

B.

S Series

C.

V Series

D.

P Series

Full Access
Question # 15

What is the correct sequence of steps used by the VxRail NVT workflow?

Full Access
Question # 16

Which license bundled with VxRail is restricted to deployments with an Embedded vCenter?

A.

vRealize Log Insight

B.

vSAN ELA

C.

Dell EMC SRS

D.

ESXi vSphere

Full Access
Question # 17

What components of a VxRail node must be assigned IP addresses?

A.

ESXi host, vCenter, ESRS. and iDRAC

B.

vSAN, vCenter, vRealize tog Insight, and vMotion

C.

ESXi host, vSAN, vCenter, and ESRS

D.

ESXi host, vSAN, vMotion, and iDRAC

Full Access