Activate Your Black Friday Offer: 75% Discount on Exam Bundles! Use coupon code below! - Ends in 0d 00h 00m 00s - Coupon code: 75onlydt

300-120 Questions and Answers

Question # 6

An engineer has configured the wireless controller to authenticate clients on the employee SSID against Microsoft Active Directory using PEAP authentication.

Which protocol does the controller use to communicate with the authentication server?

A.

EAP

B.

802.1X

C.

RADIUS

D.

WPA2

Full Access
Question # 7

A customer has Cisco FlexConnect APs at all remote branches and requires zero downtime through the FlexConnect Fault Tolerance feature. Which two configurations must be identical on both controllers to maintain connectivity when the APs switch from the primary WLC to the backup WLC because of a WAN failure? (Choose two.)

A.

AAA server ordering

B.

mobility domain

C.

interface configuration

D.

WLAN ordering

E.

AP join profile

Full Access
Question # 8

In a Cisco WLAN deployment, it is required that all Aps from branch1 remain operational even if the control plane CAPWAP tunnel is down because of a WAN failure to headquarters. Which operational mode must be configured on the APs?

A.

disconnected

B.

standalone

C.

lightweight

D.

connected

Full Access
Question # 9

An engineer needs to provision certificates on a Cisco Catalyst 9800 Series Wireless Controller. The customer uses a third-party CA server. Which protocol must be used between the controller and CA server to request and install certificates?

A.

SCEP

B.

TLS

C.

LDAP

D.

SSL

Full Access
Question # 10

What must be configured on the Global Configuration page of the WLC for an AP to use 802.1x to authenticate to the wired infrastructure?

A.

local access point credentials

B.

RADIUS shared secret

C.

TACACS server IP address

D.

supplicant credentials

Full Access
Question # 11

What must be configured on ISE version 2.1 BYOD when using Single SSID?

A.

open authentication

B.

802.1x

C.

no authentication

D.

WPA2

Full Access
Question # 12

Where is Cisco Hyperlocation enabled on a Cisco Catalyst 9800 Series Wireless Controller web interface?

A.

Policy Profile

B.

AP Join Profile

C.

Flex Profile

D.

RF Profile

Full Access
Question # 13

Refer to the exhibit.

An engineer tries to manage the rogues on the Cisco WLC. Based on the configuration, which AP is marked as malicious by the controller?

Question # 13

A.

rogue AP with SSID admin seen for 4000 seconds and heard at -70dBm

B.

rogue AP with SSID admin seen for 3000 seconds and heard at -60dBm

C.

rogue AP with SSID admin seen for 4000 seconds and heard at -60dBm

D.

rogue AP with SSID admin seen for 3000 seconds and heard at -70dBm

Full Access
Question # 14

An engineer must implement intrusion protection on the WLAN. The AP coverage is adequate and on-channel attacks are the primary concern. The building is historic, which makes adding APs difficult. Which AP mode and submode must be implemented?

A.

AP mode: local, AP submode: none

B.

AP mode: monitor, AP submode: WIPS

C.

AP mode: monitor, AP submode: none

D.

AP mode: local, AP submode: WIPS

Full Access
Question # 15

An engineer must implement Cisco Identity-Based Networking Services at a remote site using ISE to dynamically assign groups of users to specific IP subnets. If the subnet assigned to a client is available at the remote site, then traffic must be offloaded locally, and subnets are unavailable at the remote site must be tunneled back to the WLC. Which feature meets these requirements?

A.

learn client IP address

B.

FlexConnect local authentication

C.

VLAN-based central switching

D.

central DHCP processing

Full Access
Question # 16

For security purposes, an engineer enables CPU ACL and chooses an ACL on the Security > Access Control Lists > CPU Access Control Lists menu. Which kind of traffic does this change apply to as soon as the change is made?

A.

wireless traffic only

B.

wired traffic only

C.

VPN traffic

D.

wireless and wired traffic

Full Access
Question # 17

Which feature on the Cisco Wireless LAN Controller must be present to support dynamic VLAN mapping?

A.

FlexConnect ACL

B.

VLAN name override

C.

CCKM/OKC

D.

AAA override

Full Access
Question # 18

Refer to the exhibit A network engineer is using a Cisco Catalyst 9800 Series WLC to deploy a new wireless solution in a branch location Client traffic must be configured to break out locally Which code snippet must be added to the box in the code to complete the policy profile?

Question # 18

Question # 18

A.

Option A

B.

Option B

C.

Option C

D.

Option D

Full Access
Question # 19

An engineer completes the setup of a two-node Cisco ISE deployment for a guest portal. When testing the portal, the engineer notices that sometimes there is a certificate CN mismatch. Which certificate type helps resolve this issue?

A.

Public-Signed Root

B.

Public-Signed SAN

C.

Self-Signed Wildcard

D.

Self-Signed Standard

Full Access
Question # 20

A company has a single WLAN configured for 802.1x authentication with the QoS set to Silver. This WLAN supports all corporate and BYOD access. A decision has been made to allow users to install Cisco Jabber on their personal mobile devices. Users report poor voice quality when using Jabber. QoS is being applied only as best effort. What must be configured to ensure that the WLAN remains on the Silver class and to ensure Platinum class for Jabber?

A.

Configure QoS on the mobile devices that have Jabber installed.

B.

Enable Cisco Centralized Key Management on the WLAN so that the Jabber-enabled devices will connect.

C.

Configure the WLAN to broadcast on 5 GHz radios only and allow Jabber users to connect.

D.

Configure an AVC profile for the Jabber traffic and apply it to the WLAN.

Full Access
Question # 21

A company is concerned about unauthorized APs on their wired and wireless networks. The company implements a Cisco Catalyst Center (formerly DNA Center) solution. Which feature must be enabled?

A.

Rogue Management application package

B.

Neighbor Assisted Roaming

C.

Sniffer package

D.

Monitor Mode package

Full Access
Question # 22

A wireless network uses Cisco ISE to implement 802 1x for user authentication and an Active Directory server as a user database After a power outage, the wireless clients cannot connect to the wireless network The ISE log reports a "clock skew" Which action addresses this issue?

A.

Enter the correct credentials

B.

Restart the ISE service

C.

Install a trusted certificate

D.

Configure NTP

Full Access
Question # 23

Refer to the exhibit.

The security team has implemented ISE as an AAA solution for the wireless network. The wireless engineer notices that though clients are able to authenticate successfully, the ISE policies that are designed to place them on different interfaces are not working. Which configuration must be applied in the RADIUS Authentication Settings section from the ISE Network Device page?

Question # 23

A.

Disable KeyWrap.

B.

Use ASCII for the key input format.

C.

Change the CoA Port.

D.

Correct the shared secret.

Full Access
Question # 24

What is the difference between PIM sparse mode and PIM dense mode?

A.

Sparse mode supports only one switch. Dense mode supports multiswitch networks.

B.

Sparse mode floods. Dense mode uses distribution trees.

C.

Sparse mode uses distribution trees. Dense mode floods.

D.

Sparse mode supports multiswitch networks. Dense mode supports only one switch.

Full Access
Question # 25

A network engineer recently deployed Cisco Catalyst Center (formerly DNA Center) to a customer site. The customer is being flooded with alarms for wireless clients that fail AAA authentication. What is the path to disable the alarm in the Cisco Catalyst Center user interface?

A.

Assurance > Manage > Sensors

B.

Assurance > Manage > Intelligent Capture Settings

C.

Assurance > Manage > Issue Settings

D.

Assurance > Manage > Health Score Settings

Full Access
Question # 26

On a branch office deployment, it has been noted that if the FlexConnect AP is in standalone mode and loses connection to the WLC, all clients are disconnected, and the SSID is no longer advertised. Considering that FlexConnect local switching is enabled, which setting is causing this behavior?

A.

ISE NAC is enabled

B.

802.11r Fast Transition is enabled

C.

Client Exclusion is enabled

D.

FlexConnect Local Auth is disabled

Full Access
Question # 27

A wireless engineer deployed all remote sites as FlexConnect. The client VLAN assignment on these sites is configured manually mapped by WLAN and using local switching. Dynamic VLAN assignment is provided by the newly deployed Cisco ISE. Which IETF attribute must be configured on the AAA server to send that VLAN ID?

A.

Tunnel-Medium-Type

B.

Tunnel-Client-Endpoint

C.

Tunnel-Assignment-ID

D.

Tunnel-Private-Group-ID

Full Access
Question # 28

A network engineer needs to configure multicast in the network. The implementation will use multiple multicast groups and PIM routers. Which address provides automatic discovery of the best RP for each multicast group?

A.

224.0.0.13

B.

224.0.0.14

C.

224.0.1.39

D.

224.0.1.40

Full Access
Question # 29

An engineer is troubleshooting a Cisco CMX high-availability deployment and notices that the primary and backup Cisco CMX servers are both considered primary. Which command must the engineer run on the backup server?

A.

cmxha convert backup

B.

cmxha backup convert

C.

cmxha secondary convert

D.

cmxha convert secondary

Full Access
Question # 30

An engineer completed the basic installation for two Cisco CMX servers and is in the process of configuring high availability, but it fails. Which two statements about the root of the issue are true? (Choose two.)

A.

The Cisco CMX instances are installed in the same subnet.

B.

The types of the primary and secondary Cisco CMX installations differ.

C.

The delay between the primary and secondary instance is 200 ms.

D.

The sizes of the primary and secondary Cisco CMX installations differ.

E.

Both Cisco CMX installations are virtual.

Full Access
Question # 31

Exhibit:

Question # 31

Refer to the exhibit.

A wireless network engineer has been tasked with implementing AVC in a FlexConnect locally switched network. The AVC feature is properly configured for the WLAN named WLSI-AAA and the policy profile f2602. However, the AVC statistics are not displayed for this WLAN.

Which configuration change should be implemented to display the AVC statistics for this WLAN?

A.

Configure policy profile C2602 to use a different AVC policy.

B.

Configure policy profile f2602 to use a different flow monitor.

C.

Configure policy profile C2602 to use local switching for client data.

D.

Configure policy profile f2602 to use the same interface as C2602.

Full Access