In addition to coverage analysis results, what should be included in a post-deployment site survey report to ensure WLAN users experience acceptable performance is Capacity analysis results. Capacity analysis is a method of testing the ability of the WLAN to support the expected number and type of users, devices, and applications. Capacity analysis can help to determine the optimal number and placement of access points, the appropriate channel and power settings, the required QoS policies, and the expected throughput and latency levels. Capacity analysis results can help to verify that the WLAN meets the performance requirements and service level agreements (SLAs) of the organization. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-107], page 548; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-106], page 518.

The RF energy that exists in the environment from intentional and unintentional RF radiators that forms the baseline above which the intentional signal of your WLAN must exist is the best explanation of the noise floor noted in the report. The noise floor is a term that describes the level of background noise or interference in a wireless channel or band. The noise floor is measured in dBm (decibel-milliwatts) and it represents the minimum signal strength that can be detected or received by a wireless device. The noise floor is influenced by various factors, such as the sensitivity of the receiver, the antenna gain, the cable loss, and the ambient RF environment. The ambient RF environment consists of intentional and unintentional RF radiators that emit RF energy in the wireless spectrum. Intentional RF radiators are devices that are designed to transmit RF signals for communication purposes, such as Wi-Fi access points, Bluetooth devices, microwave ovens, or cordless phones. Unintentional RF radiators are devices that are not designed to transmit RF signals but generate electromagnetic radiation as a by-product of their operation, such as USB 3 devices, PC power supplies, or fluorescent lights. The noise floor affects WLAN performance and quality because it determines the minimum signal-to-noise ratio (SNR) that is required for a successful wireless transmission. SNR is the difference between the signal strength of the desired signal and the noise floor of the channel. SNR is also measured in dB and it indicates how much the signal stands out from the noise. A higher SNR means a better signal quality and a lower bit error rate. A lower SNR means a worse signal quality and a higher bit error rate. Therefore, to achieve a reliable WLAN connection, the intentional signal of your WLAN must exist above the noise floor by a certain margin that depends on the data rate and modulation scheme used. The other options are not accurate or complete explanations of the noise floor noted in the report. The noise caused by elevators, microwave ovens, and video transmitters is not the noise floor but rather examples of interference sources that contribute to the noise floor. The extra energy radiated by access points and client devices beyond that intended for the signal is not the noise floor but rather an example of spurious emissions that cause interference to other devices or channels. The energy radiated by flooring materials that causes interference in the 2.4 GHz and 5 GHz bands is not the noise floor but rather an example of attenuation or reflection that reduces or changes the direction of the signal. References: CWNA-109 Study Guide, Chapter 5: Radio Frequency Signal and Antenna Concepts, page 139

Refraction is the bending of an RF signal as it passes through a material of different density. Refraction can cause the signal to change its direction and angle of arrival. For example, when a light beam passes from air to water, it bends because of the difference in the refractive index of the two mediums. Similarly, when an RF signal passes from one medium to another, such as from air to glass, it can bend due to the change in the dielectric constant of the materials12. References: 1: CWNA-108 Official Study Guide, page 67 2: Refraction

A 5 GHz channel should be used for this AP because channels 1 and 6 are 2.4 GHz channels and they have no impact on the decision. The 5 GHz frequency band offers more non-overlapping channels than the 2.4 GHz frequency band, which reduces interference and improves performance. The 5 GHz frequency band also supports higher data rates and wider channel bandwidths than the 2.4 GHz frequency band, which increases capacity and throughput. The 5 GHz frequency band also has less interference from other devices and sources than the 2.4 GHz frequency band, which enhances reliability and quality of service. Therefore, it is recommended to use the 5 GHz frequency band for WLANs whenever possible. Channels 1 and 6 are two of the three non-overlapping channels in the 2.4 GHz frequency band (the other one is channel 11). They are used by a neighbor network in this scenario, but they do not affect the channel selection for this AP because they operate in a different frequency band than the 5 GHz frequency band. Channel 6 is not always best to use; it depends on the interference and congestion level in the environment. Channel 1 is not best to use because it has a lower frequency than channel 6; frequency does not determine channel quality or performance. Channel 11 is not best to use because it is also a 2.4 GHz channel and it may interfere with channels 1 and 6. References: CWNA-109 Study Guide, Chapter 4: Antenna Systems and Radio Frequency (RF) Components, page 113

TWT is the feature of 802.11ax (HE) that is managed with beacon and trigger frames and is primarily a power management method, but also provides more efficient access to the channel used within a BSS. TWT stands for target wake time, which is a mechanism that allows an access point and a client device to negotiate and schedule specific times for data transmission and reception. This enables the client device to enter a low-power sleep mode when it is not expected to communicate with the access point, which saves battery life and reduces power consumption. TWT also reduces contention and interference on the channel used within a BSS, as it coordinates the transmissions of multiple client devices and avoids collisions. TWT is managed with beacon and trigger frames, which are two types of management frames that are used to announce and initiate data exchanges. A beacon frame is a frame that is periodically sent by an access point to advertise its presence, capabilities, and parameters to client devices. A trigger frame is a frame that is sent by an access point or a client device to request or initiate a data transmission with another device. BSS color, UL-MU-MIMO, and OFDMA are other features of 802.11ax (HE) that are not primarily power management methods, but rather performance enhancement methods. BSS color is a feature that assigns a color code to each BSS to differentiate it from other BSSs that use the same channel. This reduces interference and improves spatial reuse of the channel. UL-MU-MIMO is a feature that allows an access point to receive multiple simultaneous transmissions from different client devices using multiple spatial streams. This increases capacity and throughput of the uplink direction. OFDMA is a feature that divides a channel into smaller subchannels called resource units (RUs) that can be allocated to different devices for concurrent transmissions. This increases efficiency and flexibility of the channel utilization. References: CWNA-109 Study Guide, Chapter 10: Wireless LAN Operation, page 323

PoE has different standards that define different power levels for PSEs and PDs. The original standard, IEEE 802.3af, defines two classes of PSEs: Class 3 (15.4 W) and Class 4 (30 W). The newer standard, IEEE 802.3at, also known as PoE+, defines four classes of PSEs: Class 0 (15.4 W), Class 1 (4 W), Class 2 (7 W), and Class 3 (12.95 W). The power level received at the PD is always lower than the power level provided by the PSE, due to cable resistance and power dissipation. The IEEE standards specify the minimum power level that must be received at the PD for each class of PSE. For a Class 4 PSE, the minimum power level received at the PD is 25.5 W910. References: CWNA-109 Study Guide, Chapter 7: Power over Ethernet (PoE), page 295; CWNA-108 Study Guide, Chapter 7: Power over Ethernet (PoE), page 289.

Patch and panel antennas are directional antenna types that are commonly used by indoor Wi-Fi devices in a MIMO multiple spatial stream implementation. These antennas have a flat rectangular shape and can be mounted on walls or ceilings to provide coverage in a specific direction. They have a moderate gain and a relatively wide beamwidth, making them suitable for multipath environments where signals can reflect off different surfaces and create multiple spatial streams. Patch and panel antennas can also support polarization diversity, which means they can transmit and receive both horizontally and vertically polarized waves, increasing the MIMO performance. References: 1, Chapter 2, page 72; 2, Section 2.4

 The most effective method for testing roaming in relation to 802.11 VoIP handsets is to place a call with the handset and move around the facility to test quality during roaming. This method allows you to evaluate the actual performance and user experience of VoIP calls over wireless networks, as well as identify any potential issues such as signal strength, interference, latency, jitter, packet loss, or handoff delays. A spectrum analyzer can only show you the RF activity during a VoIP call, but not how it affects the voice quality or roaming behavior. A protocol analyzer can capture the traffic generated when a laptop roams, but it cannot simulate the characteristics of a VoIP handset such as battery life, antenna design, codec support, or QoS features. A built-in roaming monitor is not a common feature in all VoIP handsets, and it may not provide accurate or comprehensive information about the roaming process. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-107], page 487; [Voice over Wireless LAN 4.1 Design Guide], page 6-19.

A probe request frame is a management frame that is sent by a client station to discover available wireless networks in its vicinity. A probe request can be either unicast or broadcast, depending on whether it specifies a particular SSID (Service Set Identifier) or a wildcard SSID. A broadcast probe request with a wildcard SSID is used to solicit responses from all APs within range, regardless of their SSIDs. Each AP that receives a broadcast probe request prepares a probe response frame that contains information about its network, such as SSID, supported rates, channel, security, etc. However, before sending the probe response, each AP must contend for the medium using the CSMA/CA (Carrier Sense Multiple Access with Collision Avoidance) protocol, which is the basic access method for 802.11 WLANs. This means that each AP must sense the channel for a DIFS (Distributed Interframe Space) interval, which is longer than a SIFS interval, and then generate a random backoff time before transmitting. This reduces the probability of collisions and ensures fair access to the medium among multiple APs. Therefore, each AP responds in turn after preparing a probe response and winning contention . References: [CWNA-109 Study Guide], Chapter 5: IEEE 802.11 Medium Access, page 215; [CWNA-108 Study Guide], Chapter 5: IEEE 802.11 Medium Access, page 209; [CWNA-109 Study Guide], Chapter 6: Wireless LAN Devices and Topologies, page 255.

OFDM is a modulation method that divides the channel bandwidth into multiple subcarriers, each carrying a single data symbol. This allows for higher data rates and more robust transmissions in multipath environments. OFDM was first introduced in the 802.11a standard, which operates in the 5 GHz band and supports data rates up to 54 Mbps. Later, the 802.11g standard adopted OFDM for the 2.4 GHz band, and the 802.11n and 802.11ac standards enhanced OFDM with features such as MIMO (Multiple Input Multiple Output), channel bonding, and higher-order modulation schemes to achieve data rates up to 600 Mbps and 6.9 Gbps, respectively. These standards are collectively known as the ERP (Extended Rate PHY), HT (High Throughput), and VHT (Very High Throughput) PHYs . References: [CWNA-109 Study Guide], Chapter 4: Radio Frequency Signal and Antenna Concepts, page 163; [CWNA-108 Study Guide], Chapter 4: Radio Frequency Signal and Antenna Concepts, page 157.

The error in administration that could be the cause of this security concern is that HTTP is in use instead of HTTPS. HTTP is an unencrypted protocol that transfers data in plain text over the network. This means that anyone who captures the traffic can see the HTML code of the Web pages used for access point management, as well as any sensitive information such as passwords or configuration settings. HTTPS is an encrypted protocol that uses SSL/TLS to secure the data transmission between the Web browser and the Web server. HTTPS prevents anyone from snooping on or tampering with the Web traffic. Therefore, HTTPS should always be used for Web based management of wireless access points, especially in autonomous mode where there is no centralized controller to enforce security policies. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-107], page 431; [HTTP vs HTTPS: What’s The Difference And Why Should You Care?].

CCI is still a possibility in this network because the client devices connected to one of the channel 1 APs will transmit frames that reach the other channel 1 AP as well as clients connected to the other channel 1 AP. CCI stands for co-channel interference, which is a type of interference that occurs when two or more devices transmit on the same channel within range of each other. CCI reduces performance and capacity because it causes contention and collisions on the wireless medium, which leads to retransmissions and delays. CCI can be mitigated by increasing physical separation between devices using the same channel or by reducing transmit power levels to limit coverage area. In this scenario, three access points are used within a facility. One access point is on channel 11 and the other two are on channel 1. The two access points using channel 1 are on either side of the access point using channel 11 and sufficiently apart so that they do not interfere with each other when they transmit frames. However, this does not prevent CCI from occurring between their client devices that are connected on channel 1. For example, if a client device connected to one of the channel 1 APs sends a frame to another device on the wired network or on another wireless network (such as an Internet server or a VoIP phone), that frame will be heard by both channel 1 APs as well as any other client devices connected to either of them on channel 1. This will cause CCI because these devices will have to wait for the channel to be clear before they can transmit their own frames. The answer that CCI only occurs in the 5 GHz frequency band is incorrect; CCI can occur in any frequency band where devices use the same channel. The answer that channel 11 loops around and causes CCI with channel 1 is also incorrect; channel 11 does not loop around and it operates in a different frequency band than channel 1. References: CWNA-109 Study Guide, Chapter 5: Radio Frequency Signal and Antenna Concepts, page 147

Passive Gain is the increase of RF energy in an intentional direction with the use of an antenna. It is achieved by focusing the same amount of power into a smaller area, resulting in a higher power density and a stronger signal. Passive Gain does not require any additional power or amplification, but rather depends on the antenna’s physical characteristics, such as size, shape, and orientation. Passive Gain is also expressed in decibels (dB) and is related to the antenna’s beamwidth and directivity. References: 1, Chapter 2, page 63; 2, Section 2.3

 This is because the passphrase for WPA2-Personal is case-sensitive and must match exactly on both the AP and the client. If the passphrase is entered incorrectly on the client, the client will not be able to authenticate with the AP and connect to the network. The AP that covers the problem area is not likely to require a firmware update, fail, or be improperly configured, as it is online and works with other clients that have the correct passphrase. To troubleshoot this issue, you can check the passphrase settings on the clients and make sure they match with the AP. You can also try to reconnect the clients to the network or reboot them if necessary. For more information on how to configure WPA2-Personal on your router

A high-density deployment is a wireless network that is designed to support a large number of users and devices in a relatively small area. This type of deployment is often used in enterprise environments, such as offices, schools, and hospitals.

The use of semi-directional antennas in the deployment described in the question is a good indication that it is a high-density deployment. Semi-directional antennas can be used to focus the signal from an access point in a specific direction. This can help to reduce interference and improve performance in high-density environments.

The other answer choices are less likely to be correct for the following reasons:

• SOHO (small office/home office) deployments are typically smaller and less complex than high-density deployments.
• Residential deployments are typically even smaller and less complex than SOHO deployments.
• Standard office deployments may be high-density, but they may also be lower-density.

It is important to note that the type of deployment is not determined solely by the output power of the access points. However, the use of 10 mW of output power on the 2.4 GHz radios and 20 mW of output power on the 5GHz radios is also consistent with a high-density deployment.

Here are some additional tips for deploying a high-density wireless network:

• Use a site survey to determine the optimal placement of access points.
• Configure the access points to use non-overlapping channels.
• Use semi-directional or directional antennas to focus the signal and reduce interference.
• Implement a wireless intrusion prevention system (WIPS) to detect and mitigate rogue access points and other security threats.

DHCP (Dynamic Host Configuration Protocol) is the network service where option 43 must be configured to allow access points to locate controllers. DHCP is a protocol that allows a device to obtain an IP address and other network configuration parameters from a server. In a wireless controller scenario, the access points can use DHCP to request an IP address from a DHCP server, which can also provide the IP address or hostname of the wireless controller as an option in the DHCP response. Option 43 is a vendor-specific option that can be used to encode custom information for different types of devices. For example, Cisco access points can use option 43 to receive the IP address of the wireless controller from the DHCP server, while Aruba access points can use option 43 to receive the hostname of the wireless controller from the DHCP server. This way, the access points can discover the wireless controller and establish a connection with it. References: 1, Chapter 8, page 309; 2, Section 5.2

 VSWR stands for Voltage Standing Wave Ratio, which is a measure of how well the impedance of the RF cable and connectors matches the impedance of the transmitter and the antenna. Impedance is the opposition to the flow of alternating current in an RF circuit, and it depends on the frequency, resistance, capacitance, and inductance of the components. A perfect impedance match would have a VSWR of 1:1, meaning that all the power is transferred from the transmitter to the antenna, and none is reflected back. However, in reality, there is always some degree of mismatch, which causes some power to be reflected back to the transmitter, creating standing waves along the cable. This reduces the efficiency and performance of the wireless system, and can also damage the transmitter. Excessive VSWR can be caused by using poor quality or damaged cables and connectors, or by using components that have different impedance ratings123. References: CWNA-109 Study Guide, Chapter 2: Radio Frequency Fundamentals, page 90; CWNA-108 Study Guide, Chapter 2: Radio Frequency Fundamentals, page 86; CWNP website, CWNA Certification.

The distance at which an RF signal can be effectively received depends on several factors, such as the transmitting station’s output power, the free space path loss, the receiving station’s radio sensitivity, and the environmental noise and interference. However, the receiving station’s output power does not influence this distance, because it only affects how well the receiving station can transmit signals back to the transmitting station. The output power of the receiving station is irrelevant for receiving signals from the transmitting station12. References: CWNA-109 Study Guide, Chapter 2: Radio Frequency Fundamentals, page 79; CWNA-108 Study Guide, Chapter 2: Radio Frequency Fundamentals, page 74.

PoE stands for Power over Ethernet, which is a technology that allows network devices to receive power and data over the same Ethernet cable. PoE eliminates the need for separate power adapters or outlets for devices such as IP phones, cameras, or APs. PoE requires two types of devices: PSE (Power Sourcing Equipment) and PD (Powered Device). A PSE is a device that provides power to the Ethernet cable, such as a switch, injector, or splitter. A PD is a device that receives power from the Ethernet cable, such as an IP phone, camera, or AP. When implementing PoE, a switch plays the role of a PSE910. References: CWNA-109 Study Guide, Chapter 7: Power over Ethernet (PoE), page 293; CWNA-108 Study Guide, Chapter 7: Power over Ethernet (PoE), page 287.

Channel 144 is a new channel that was added to the 5 GHz band by the 802.11ac amendment, which defines the VHT (Very High Throughput) PHY for WLANs. Channel 144 has a center frequency of 5720 MHz and a bandwidth of 20 MHz. It can also be combined with adjacent channels to form wider channels of 40 MHz, 80 MHz, or 160 MHz. Channel 144 is available in some regions, such as North America and Europe, but not in others, such as Japan and China . References: [CWNA-109 Study Guide], Chapter 3: Antennas and Accessories, page 121; [CWNA-108 Study Guide], Chapter 3: Antennas and Accessories, page 115; [Wikipedia], List of WLAN channels.

 The frame type that is used to reserve the wireless medium for the transmission of high data rate frames that may not be understood by all clients connected to the BSS is RTS. RTS stands for Request to Send and is a control frame that is sent by a station to request access to the medium for a specified duration. The RTS frame contains the source and destination MAC addresses, as well as a Network Allocation Vector (NAV) value that indicates how long the medium will be occupied. The destination station responds with a Clear to Send (CTS) frame that echoes the NAV value and grants permission to the source station. All other stations in the BSS hear either the RTS or CTS frame and update their NAV timers accordingly, deferring their transmissions until the medium is free. The RTS/CTS mechanism can be used to prevent hidden node problems, reduce collisions, and protect high data rate frames that use features such as 802.11n or 802.11ac that may not be compatible with legacy stations. ACK, Beacon, and PS-Poll are not used to reserve the medium for high data rate frames. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-107], page 112; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-106], page 102.

https://www.wlanmall.com/what-is-a-wireless-bridge/

Wireless bridging is a WLAN technology role that allows two or more networks to be connected wirelessly over a distance. A wireless bridge consists of two or more APs that are configured to operate in bridge mode and use directional antennas to establish a point-to-point or point-to-multipoint link. Wireless bridging can support high data rates and is suitable for scenarios where running cables is impractical or expensive. To create a wireless link between two buildings on a single campus that supports at least 150 Mbps data rates, wireless bridging is an appropriate solution678. References: CWNA-109 Study Guide, Chapter 6: Wireless LAN Devices and Topologies, page 271; CWNA-108 Study Guide, Chapter 6: Wireless LAN Devices and Topologies, page 265; Wi-Fi Wireless Bridging Explained.

SAE (Simultaneous Authentication of Equals) is required when operating 802.11ax APs in the 6 GHz band using passphrase-based authentication. SAE is a secure and robust authentication method that is defined in the IEEE 802.11s amendment and is also known as WPA3-Personal or WPA3-SAE. SAE is based on a cryptographic technique called Dragonfly Key Exchange, which allows two parties to establish a shared secret key using a passphrase, without revealing the passphrase or the key to an eavesdropper or an attacker. SAE also provides forward secrecy, which means that if the passphrase or the key is compromised in the future, it does not affect the security of past communications.

SAE is required when operating 802.11ax APs in the 6 GHz band using passphrase-based authentication because of the new regulations and standards that apply to this band. The 6 GHz band is a new frequency band that was opened for unlicensed use by the FCC and other regulatory bodies in 2020. The 6 GHz band offers more spectrum and less interference than the existing 2.4 GHz and 5 GHz bands, which can enable higher performance and efficiency for Wi-Fi devices. However, the 6 GHz band also has some restrictions and requirements that are different from the other bands, such as:

• The 6 GHz band is divided into two sub-bands: U-NII-5 (5925-6425 MHz) and U-NII-7 (6525-6875 MHz). The U-NII-5 sub-band is subject to DFS (Dynamic Frequency Selection) rules, which require Wi-Fi devices to monitor and avoid using channels that are occupied by radar systems or other primary users. The U-NII-7 sub-band is not subject to DFS rules, but it has a lower maximum transmit power limit than the U-NII-5 sub-band.
• The Wi-Fi devices that operate in the 6 GHz band are called 6E devices, which stands for Extended Spectrum. 6E devices must support 802.11ax technology, which is also known as Wi-Fi 6 or High Efficiency (HE). 802.11ax is a new standard that improves the performance and efficiency of Wi-Fi networks by using features such as OFDMA (Orthogonal Frequency Division Multiple Access), MU-MIMO (Multi-User Multiple Input Multiple Output), BSS Coloring, TWT (Target Wake Time), and HE PHY and MAC enhancements.
• The 6E devices that operate in the 6 GHz band must also support WPA3 security, which is a new security protocol that replaces WPA2 and provides stronger encryption and authentication for Wi-Fi networks. WPA3 has two modes: WPA3-Personal and WPA3-Enterprise. WPA3-Personal uses SAE as its authentication method, which requires a passphrase to establish a secure connection between two devices. WPA3-Enterprise uses EAP (Extensible Authentication Protocol) as its authentication method, which requires a certificate or a credential to authenticate with a server.

Therefore, SAE is required when operating 802.11ax APs in the 6 GHz band using passphrase-based authentication because it is part of WPA3-Personal security, which is mandatory for 6E devices in this band. References: , Chapter 3, page 120; , Section 3.2

9of30

The least expensive solution available for increasing throughput for these users without implementing configuration options that are not recommended is to use a 40 MHz channel on the 5 GHz radio. This solution can double the channel bandwidth and increase the data rates for the 5 GHz capable 802.11ac clients. Using a 40 MHz channel on the 5 GHz radio is also less likely to cause co-channel interference or overlap with other channels than using a 40 MHz channel on the 2.4 GHz radio, which has only three non-overlapping channels. Using a 160 MHz channel on the 5 GHz radio may provide even higher throughput, but it may also consume too much of the available spectrum and cause more interference with other devices or networks. Installing a second AP in the coverage area may also improve the throughput, but it may require additional costs and configuration. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-107], page 216; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-106], page 206.

A BSS (Basic Service Set) is a WLAN use case that represents an 802.11-based network that uses an AP (Access Point) and has several connecting clients. The AP acts as a central point of coordination and communication for the clients, which can include iPhones, iPads, laptops, desktops, or any other devices that have Wi-Fi capabilities. A BSS can be identified by a unique BSSID (Basic Service Set Identifier), which is usually the MAC address of the AP’s radio interface. A BSS can also be associated with an SSID (Service Set Identifier), which is a human-readable name that identifies the network. References: , Chapter 1, page 23; , Section 1.1

 iPerf is an open source tool that is designed to perform a throughput test on the WLAN. iPerf is a cross-platform command-line tool that can measure the bandwidth and quality of network links by generating TCP or UDP traffic between two endpoints. iPerf can run as either a server or a client mode, depending on whether it receives or sends traffic. iPerf can also report various metrics of network performance, such as throughput, jitter, packet loss, delay, and TCP window size. To perform a throughput test on the WLAN using iPerf, one device needs to run iPerf in server mode and another device needs to run iPerf in client mode. The devices need to be connected to the same WLAN network and have their IP addresses configured properly. The device running iPerf in client mode needs to specify the IP address of the device running iPerf in server mode as well as other parameters such as protocol, port number, duration, interval, bandwidth limit, packet size, etc. The device running iPerf in server mode will listen for incoming connections from the client device and send back acknowledgments or responses depending on the protocol used. The device running iPerf in client mode will send traffic to the server device according to the specified parameters and measure the network performance. The device running iPerf in client mode will display the results of the throughput test at the end of the test or at regular intervals during the test. The results can show the average, minimum, maximum, and instantaneous throughput of the network link, as well as other metrics such as jitter, packet loss, delay, and TCP window size. References: 1, Chapter 7, page 287; 2, Section 4.3

When performing a post-deployment validation survey for voice over Wi-Fi (VoWiFi), an action that must be performed is Application analysis with an active phone call on a VoWiFi handset. Application analysis is a method of testing the performance of a specific application over the WLAN by measuring parameters such as throughput, latency, jitter, packet loss, MOS score, and R-value. Application analysis with an active phone call on a VoWiFi handset can help to evaluate the quality of service (QoS) and user experience of VoWiFi calls over the WLAN. It can also help to identify any issues or bottlenecks that may affect VoWiFi calls such as interference, roaming delays, or insufficient coverage. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-107], page 549; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-106], page 519.

An isotropic radiator is a theoretical point source of electromagnetic radiation that radiates equally in all directions. It has no physical dimensions and no preferred direction of radiation. It is used as a reference for antenna gain because it represents the ideal case of a perfect omnidirectional antenna12

Antenna gain is a measure of how well an antenna concentrates its radiated power in a certain direction. It is expressed in decibels (dB) relative to a reference antenna. When the reference antenna is an isotropic radiator, the antenna gain is denoted by dBi, which stands for decibels relative to isotropic12

For example, an antenna with a gain of 3 dBi means that it radiates 3 dB more power in its main direction than an isotropic radiator would. Conversely, an antenna with a gain of -3 dBi means that it radiates 3 dB less power in its main direction than an isotropic radiator would12

Based on the information given, what can be determined as certainly true about this AP is that it has 4 radio chains. A radio chain is a hardware component that consists of an antenna, a radio frequency (RF) amplifier, and a transceiver. The number of radio chains indicates how many spatial streams an AP can transmit or receive simultaneously using Multiple Input Multiple Output (MIMO) technology. The notation x:y:z in an AP specification denotes the number of radio chains (x), the number of spatial streams (y), and the number of spatial streams per band (z). Therefore, a tri-band, 4x4:4, Wi-Fi 6, 802.11ax AP has four radio chains in each of its three bands (2.4 GHz, low 5 GHz, and high 5 GHz). It also supports four spatial streams in total and four spatial streams per band. It cannot be determined as certainly true that it supports four channels in each band, UL-MU-MIMO, or uses a modified OpenWRT firmware based on the information given. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-107], page 223; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-106], page 213.

The center frequency of channel 4 in the 2.4 GHz band is 2.427 GHz (2427 MHz). The center frequency of a channel is the midpoint of its frequency range, where the signal strength is highest and most concentrated. The center frequency of channel 1 in the 2.4 GHz band is 2.412 GHz (2412 MHz), as given in the question. The center frequency of each subsequent channel is obtained by adding 5 MHz to the previous channel’s center frequency, since the channels are spaced 5 MHz apart from each other in this band. Therefore, to find the center frequency of channel 4, we need to add 15 MHz (5 MHz x 3) to the center frequency of channel 1:

2.412 GHz + 0.015 GHz = 2.427 GHz

Alternatively, we can use a formula to calculate the center frequency of any channel in the 2.4 GHz band:

Center frequency (GHz) = 2.407 + (0.005 x Channel number)

Using this formula for channel 4, we get:

Center frequency (GHz) = 2.407 + (0.005 x 4)

Center frequency (GHz) = 2.407 + 0.02

Center frequency (GHz) = 2.427 References: 1, Chapter 3, page 85; 2, Section 3.2

Station-to-station traffic blocking is a security feature that prevents wireless clients from communicating with each other on the same network. This can prevent active attacks such as man-in-the-middle, ARP spoofing, or denial-of-service that hackers may launch from their devices against other users in a public Wi-Fi hotspot. By enabling station-to-station traffic blocking by the access points in the hotel, Lynne can decrease the likelihood of such attacks on his customers’ wireless computers. This feature can be configured on most wireless APs or controllers345. References: CWNA-109 Study Guide, Chapter 10: Wireless LAN Security, page 427; CWNA-108 Study Guide, Chapter 10: Wireless LAN Security, page 417; Wireless Station-to-Station Traffic Being Blocked.