300-615 Dumps with Practice Exam Questions Answers

The correct answer is Update the CNA firmware and driver versions. Cisco MDS and Nexus SAN troubleshooting is driven by fabric state: the host and target must be in the correct VSAN, must complete FLOGI/PLOGI where applicable, and must be permitted by active zoning, fcdomain, FSPF, NPV/NPIV, or port-security policy. This question focuses on firmware, Cisco Nexus, so the selected action fixes the dependency that prevents the initiator, target, or inter-switch link from becoming usable. Cisco documentation emphasizes checking VSAN membership, active zonesets, correct port mode, fabric binding, device-alias consistency, and the relevant FC databases before changing unrelated server settings. The distractors either target a different database, use the wrong port role, or would not cause the observed Fibre Channel state to change. After the fix, the engineer should confirm the interface state, FLOGI database, name-server entries, zoneset activation, and successful initiator-to-target reachability with tools such as fcping or fabric show commands.

Install Infrastructure Firmware, then Install Server Firmware is correct because the failure is tied to the UCS managed state of UCS, firmware, Auto Install. In Cisco UCS, policies are not advisory; they are the source from which fabric interconnects program adapters, boot targets, server identity, firmware, and external integrations. A mismatch between the policy and the actual hardware or upstream storage/network state can cause boot, discovery, KVM, firmware, or connectivity failures. The selected action addresses the object that UCS Manager uses to build the final operational configuration. The distractors either solve a different fault domain or bypass the policy model. A disciplined DCIT validation sequence is to check the fault code, the FSM history, the equipment inventory, the service profile association, and the relevant adapter or boot table. If those states are correct after the change, the UCS component should return to operable service without unnecessary reconfiguration.

The applet called “Backup” must include an action to remove the current static route is the valid corrective action because the failure described is a protocol or fabric state problem, not a generic connectivity issue. For Cisco Nexus, Cisco troubleshooting expects the engineer to compare both endpoints of the relationship: vPC peers must agree on consistency parameters, HSRP peers must exchange hellos in the same VLAN and version context, OSPF/BGP peers must match the attributes required for stable adjacency, and VXLAN EVPN must advertise the correct host or prefix information. The selected option restores that required state. The other options either operate on the wrong layer, change a value that is not used to form the relationship, or would make the peer relationship less deterministic. A clean validation is to inspect the control-plane table first, then verify the forwarding table, and finally test end-to-end traffic. This is the Cisco-preferred approach because it avoids random changes and confirms that the fabric is forwarding based on correct protocol state.

Configure the Filter field with sAMAccountName=$company is the appropriate UCS remediation because the symptom maps to a specific managed object rather than a generic server failure. Cisco UCS abstracts hardware through service profiles and policies; therefore, issues involving UCS, UCS Manager, LDAP must be corrected where UCS Manager programs the adapter, boot target, firmware, management certificate, pool qualification, or fabric interconnect state. The selected answer restores that programming path. The other options may appear plausible, but they do not correct the object that UCS uses to derive operational state. For example, boot failures require the correct vHBA/iSCSI target and LUN policy, discovery issues require the proper physical and management path, and firmware failures require the documented recovery action for the failed FSM stage. The correct validation is to inspect the associated fault, confirm inventory acknowledgment, verify the policy under the service profile or equipment tree, and then recheck boot or connectivity behavior after the FSM completes.

The correct answer is shell:domains=Security_Domain_1/Read_Role_1|Read_Role_2. Cisco management and operations troubleshooting focuses on control-plane services such as RBAC, AAA, certificates, SNMP, firmware packages, centralized management registration, fault workflows, and node lifecycle state. This item references the affected data-center component, so the selected action fixes the management dependency rather than the data-plane symptom. Cisco platforms often allow basic reachability while a higher-level integration still fails because of time synchronization, certificate trust, role mapping, authorization attributes, feature state, or incomplete lifecycle cleanup. The other options either modify forwarding behavior, adjust the wrong credential or role, or bypass the required operational workflow. The engineer should validate the fix by confirming the management session or registration, checking the relevant fault or audit log, and confirming that the user, node, or integration has the expected role and operational status. This is consistent with Cisco DCIT emphasis on operational evidence before and after the change.