Which of the following server configurations is recommended for the optical fiber sensing scenario?
128 GB configuration
384 GB configuration
512 GB configuration
Relevant Training Extract — HUAWEI NCE-T Product Introduction, Page 125
“Optical fiber sensing — Commercial use — O1-Fiber Sensing Vibration Warning System Management Basic Package — management”
Technical Deep Dive:
Huawei ' s optical fiber sensing solution incorporates distributed sensing equipment, event analysis, alarm processing, geographic visualization, and centralized management.
Optical sensing systems generate information about disturbances along monitored fiber routes. Depending on the implementation, these disturbances may be classified using signal-processing algorithms and machine-learning techniques.
Server resource planning must account for the monitored fiber scale, sensing event volume, number of managed devices, data retention requirements, and software processing architecture.
A larger memory configuration may be selected where the management infrastructure includes substantial analytics, correlation, or virtualization workloads.
The intended answer identifies a 384 GB server configuration for the referenced sensing deployment.
However, server sizing must distinguish between the physical machine deployment model and virtualized deployments. They may have different memory requirements even when they support similar business functions.
Technical Conclusion: B is the answer intended by the question set, but it cannot be established as a universal requirement from the uploaded training material.
Verification warning: The Huawei training identifies the sensing management function but does not specify a 384 GB memory requirement. Other Huawei release documentation identifies a 128 GB physical server for an optical-fiber sensing scenario and 384 GB for a combined Manager/Controller/Analyzer virtualized configuration. Consequently, this question requires an explicit software release and deployment scenario before a single memory recommendation can be considered fully verified.
Which of the following protection schemes does the OptiXtrans E6600 series support?
Select All that Apply
ODUk SNCP
Client 1+1 protection
OLP
IP RAN
Relevant Training Extract — Huawei E9600 and E6600 Series Products and Industry Applications Introduction, Page 33
“Full SDH protection”
The protection architecture includes Subnetwork Connection Protection (SNCP), Multiplex Section Protection (MSP), and related network protection mechanisms.
Additional Official Huawei Technical Reference — OptiXtrans E6616 Product Brochure
“Client 1+1 protection, intra-board 1+1 protection, ODUk SNCP, optical line protection”
Technical Deep Dive:
Huawei OptiXtrans E6600 equipment supports multiple protection mechanisms to improve optical network availability and reduce the service impact of equipment and transmission failures.
Option A — ODUk SNCP (Correct):
ODUk Subnetwork Connection Protection provides protection at the OTN electrical-layer service level. A service can be transmitted along protected paths, allowing the receiving equipment to select the suitable signal when degradation or failure occurs.
Option B — Client 1+1 protection (Correct):
Client-side 1+1 protection provides redundant transmission resources for customer-facing services. A protected service can be carried through working and protection resources so that a single qualifying failure does not necessarily interrupt service availability.
Option C — OLP (Correct):
Optical Line Protection protects optical fiber transmission paths. It can switch optical traffic between working and protection fiber routes when supported failure conditions occur.
Option D — IP RAN (Incorrect):
IP Radio Access Network is a network architecture used to transport mobile radio access traffic. It is not itself an optical transport protection mechanism.
Huawei E6600 platforms may transport IP RAN services, but that does not make IP RAN a protection scheme.
Technical Conclusion: A, B, and C are correct. The precise protection features available depend on the platform model, boards, software release, and network configuration.
Which of the following quotation items is included by default in the service-provisioning function of enterprise NCE-T?
Latency map function package
Basic OTN management function package
BoD/BC function package
Optical fiber intelligent management function package
Relevant Training Extract — HUAWEI NCE-T Product Introduction, Page 124
“Automatic provisioning”
The NCE-T management architecture distinguishes network management, service provisioning, and advanced intelligent O & M functions.
Additional Training Reference — Page 125
The Huawei use-case quotation matrix separately identifies the BOD/BC function package, latency map function package, and optical fiber intelligent management function package.
Technical Deep Dive:
Huawei iMaster NCE-T provides centralized optical network management and control capabilities, including network element management, resource supervision, service provisioning, topology visualization, and fault management.
The Basic OTN management function package is the intended baseline commercial item for enterprise OTN management and associated service-provisioning operations.
The baseline management capability provides the foundation on which additional service automation and intelligent network functions can be deployed.
Option A — Latency map: This is a value-added capability associated with latency visualization, service assurance, and latency-aware operations. It is not the intended default basic management package.
Option B — Basic OTN management: This is the intended baseline selection for enterprise OTN management and service provisioning.
Option C — BoD/BC: Bandwidth on Demand and Bandwidth Calendar provide flexible capacity adjustment and scheduled bandwidth provisioning. Huawei identifies these capabilities as separately selectable use-case packages.
Option D — Optical fiber intelligent management: This is associated with intelligent optical fiber supervision and GIS-related management rather than the baseline OTN service-provisioning entitlement.
For accurate quotations, the engineer must distinguish mandatory foundational licensing from additional functional packages.
Technical Conclusion: B is the intended answer.
Verification qualification: The uploaded training directly identifies the separately quoted value-added packages, but it does not explicitly establish that the Basic OTN management function package is included by default in every enterprise NCE-T service-provisioning offering. That precise default-selection rule requires confirmation against the applicable commercial offering catalog.
Which of the following specifies the internal power supply of the E9605?
2+2 backup, rated current 60 A
1+2 backup, rated current 60 A
1+1 backup, rated current 32 A
1+2 backup, rated current 32 A
Exact Extract — E9600 and E6600 Series Products and Industry Applications Introduction, Page 11
“Power supply: 1+1 32 A”
The E9605 hardware diagram identifies PIU/APIU locations IU100 and IU101, together with the supported internal power-supply arrangements.
Technical Deep Dive:
The OptiXtrans E9605 is a compact 4U optical-layer subrack designed for optical line amplifier and ROADM applications.
High availability is important because failure of a power supply at an optical transmission site can interrupt services carried through multiple wavelengths.
The E9605 uses a redundant internal power architecture with 1+1 protection.
In this arrangement, two power-input units provide redundancy so that a single power-input failure does not automatically cause an equipment outage, provided the remaining source and module can sustain the required load.
The specified rated current for the supported internal power arrangement is 32 A.
Option A incorrectly describes a 2+2 architecture and a 60 A rating. Options B and D incorrectly describe 1+2 redundancy.
Huawei ' s hardware specifications identify internal DC, AC, and HVDC power-supply options, depending on the product configuration.
For an actual deployment, engineers must verify the selected power variant, supply voltage, branch-circuit protection, earthing, power consumption, and redundancy requirements.
Technical Conclusion: C is correct because the E9605 supports a 1+1 redundant power-supply architecture with a specified 32 A rating.
Which of the following statements concerning the E9624 power supply solution is true?
PIUs in IU100 and IU101 back up each other and provide power supply for the entire area.
PIUs IU100 and IU105 back up each other and provide power supply for different areas.
PIUs IU101 and IU105 back up each other and provide power supply for different areas.
PIUs IU100 and IU106 back up each other and provide power supply for the entire area.
Exact Extract — E9600 and E6600 Series Products and Industry Applications Introduction, Page 6
“PIU (IU100/IU105, IU101/IU106), 2+2 power supply protection (area-based power supply), DC (internal)/AC (external)”
Technical Deep Dive:
The Huawei OptiXtrans E9624 uses a redundant power-supply architecture designed to improve equipment availability and reduce the risk of service interruption caused by a single power-input failure.
The E9624 provides four Power Interface Unit (PIU) positions: IU100, IU101, IU105, and IU106.
The redundancy relationships are:
• IU100 and IU105 form a mutual-backup pair.
• IU101 and IU106 form another mutual-backup pair.
The architecture implements 2+2 power protection with area-based power distribution.
Option A — Incorrect: IU100 and IU101 are not the specified mutual-backup pair.
Option B — Correct: IU100 and IU105 are paired for redundancy and operate within the area-based power-supply architecture.
Option C — Incorrect: IU101 and IU105 do not form the specified mutual-backup relationship.
Option D — Incorrect: IU100 and IU106 are not the designated backup pair.
The use of redundant power inputs allows the E9624 to maintain operation following qualifying single-input failures, provided the remaining power infrastructure can supply the required load.
For critical enterprise deployments, independent power feeds should be planned according to the supported power distribution arrangement.
Technical Conclusion: B is correct.
Answer-key correction: The original supplied explanation identifies IU100 and IU101 as the redundant pair. Huawei ' s hardware diagram instead establishes IU100/IU105 and IU101/IU106 as the relevant backup pairs.
What advantage does Liquid OTN have over MS-OTN?
Different service types
More service connections
Lower encapsulation latency
Higher bandwidth efficiency
Exact Extract — Huawei E9600 and E6600 Series Products and Industry Applications Introduction, Page 23
“More service connections, higher bandwidth efficiency, and lower encapsulation latency”
Additional Exact Extract — Page 23
“2 Mbit/s slicing, increasing the number of connections by 12.5 times”
Technical Deep Dive:
Liquid OTN uses Optical Service Unit (OSU) technology to provide flexible, fine-granularity hard-pipe transmission for services with different bandwidth requirements.
Traditional Multi-Service OTN (MS-OTN) supports multiple service switching planes, including virtual container, packet, and ODUk switching.
Although this architecture accommodates different service types, conventional ODU container granularities can result in inefficient bandwidth allocation for low-rate services.
For example, a 100 Mbit/s service mapped into an ODU0 container with a nominal capacity of approximately 1.25 Gbit/s consumes significantly more transport capacity than the service requires.
Liquid OTN introduces flexible bandwidth allocation down to 2 Mbit/s granularity, allowing service containers to match customer requirements more closely.
This reduces unused bandwidth and improves the utilization of optical transport resources.
Liquid OTN also supports more service connections through finer slicing and reduces encapsulation overhead by simplifying the multiplexing architecture.
Technical Conclusion: D is the intended single-choice answer because higher bandwidth efficiency is a principal Liquid OTN advantage.
Important ambiguity: The training explicitly confirms that B, C, and D are all valid advantages. Because the question does not say “Select All that Apply,” it lacks a uniquely defensible single answer. A corrected multi-select version should use B, C, D, or the question should specifically ask which benefit results from more precise bandwidth allocation.
Which of the following statements about the license configuration of enterprise WDM series are correct?
Select All that Apply
The cross-connect capacity license is used to control the expansion of the port capacity.
If the Fiber Doctor function is selected on the DC908, the intelligent fiber monitoring license will be configured.
To configure Liquid OTN services on the port of the line board, a Liquid OTN license is required.
If the IEEE 1588v2 feature is required, each set of devices on the clock tracing path requires one IEEE 1588v2 function license.
Exact Extract — Network Planning, Design, Configuration and Quotation Guide, Pages 61 and 67
“Capacity of Centralized Cross Connect Board: This parameter is used to configure a centralized cross-connect capacity license.”
“Need 1588V2 Function or not: If the IEEE 1588v2 feature is required, each device on the clock tracing path requires one piece of IEEE 1588v2 function software.”
Technical Deep Dive:
Huawei enterprise WDM systems use software licensing to enable selected optical transport capabilities and control the expansion of licensed resources.
Option A — Incorrect. A cross-connect capacity license controls the amount of traffic that the cross-connect architecture is authorized to switch or groom. Physical port capacity and line-port activation are distinct licensing dimensions. Increasing the cross-connect capacity does not automatically authorize additional physical line-port capacity.
Option B — Correct under the intended licensing scheme. Fiber Doctor provides optical fiber monitoring and fault-localization capabilities. It can use embedded OTDR technology to detect fiber abnormalities, locate faults, and support proactive optical cable maintenance. The associated intelligent fiber monitoring entitlement must be included where the feature is separately licensed.
Option C — Correct under the intended licensing scheme. Liquid OTN enables fine-granularity hard-pipe service transmission. Applicable line-board functions may require corresponding feature entitlements to support OSU-based service transport.
Option D — Correct. IEEE 1588v2 supports precision time synchronization through Precision Time Protocol (PTP) messaging. Every participating network element that requires the licensed synchronization functionality must be appropriately authorized.
Licensing only the source and destination devices is insufficient when intermediate devices are required to process or regenerate timing information.
Technical Conclusion: B, C, and D are the intended selections. The supplied training explicitly establishes D and the distinction underlying A. The exact Fiber Doctor and Liquid OTN license-product mappings in B and C require release-specific SCT verification; they are not individually documented in the uploaded slides.
What are the customer requirements for the transport network in the smart high-speed railway era?
Select All that Apply
Easy O & M, fast service provisioning, intelligent monitoring, and intelligent optimization
High bandwidth to accommodate increasing lines, sites, services, and cloud storage
Multi-service (GSM-R, LTE-R, and 5G) transmission
High reliability, high security, and physical isolation of important security services
Exact Extract — E9600 and E6600 Series Products and Industry Applications Introduction, Page 44
“GSM-R and 5G-based FRMCS, PCM interface, SDH, and IP will co-exist for long time.”
“Seamless service interconnection should be considered in network evolution.”
Additional Training Reference — Page 45
The railway bearer network architecture identifies multi-service access, large bandwidth, low latency, high reliability, synchronization, and smart OAM as its principal requirements.
Technical Deep Dive:
Modern railway communication networks support operational systems with different service characteristics, bandwidth requirements, and reliability expectations.
Option A — Correct: Intelligent operation and maintenance is necessary to manage extensive railway transmission networks. Centralized management, rapid fault localization, service provisioning, and performance monitoring reduce operational complexity and improve maintenance efficiency.
Option B — Correct: High-speed railways generate increasing volumes of operational and passenger-related data. Video surveillance, train monitoring, dispatching applications, and cloud-connected systems require scalable high-bandwidth transmission.
Option C — Correct: Railway networks must accommodate the transition from legacy GSM-R communications toward newer railway radio technologies and 5G-based Future Railway Mobile Communication System (FRMCS) architectures. Legacy and next-generation services may coexist during network modernization.
Option D — Correct: Railway control and signaling are safety-critical applications. The transport infrastructure must provide robust protection, secure service separation, predictable latency, and high availability.
Huawei ' s MS-OTN and optical hard-pipe technologies help satisfy these requirements through deterministic transmission, multi-service convergence, and physical resource isolation.
Technical Conclusion: A, B, C, and D are correct. All four represent fundamental railway transmission network requirements.
If no board is quoted, the E9624 is automatically configured with two 30-meter pigtails. Which of the following statements is true?
Optical modules are configured by default.
The default configuration is incorrect.
These pigtails are reserved by default to connect the FIU and ODF.
Exact Extract — Network Planning, Design, Configuration and Quotation Guide, Page 63
“The Length of Patch Cord Connecting to Customer ' s ODF: The length of fiber patch cords is calculated based on the distance between the cabinet and the customer ' s ODF.”
Technical Deep Dive:
The OptiXtrans E9624 is an optical-electrical integrated transmission platform that supports the deployment of optical-layer and electrical-layer functions within the same equipment architecture.
During optical network installation, physical fiber connectivity must be planned independently of the number of service boards installed.
The Fiber Interface Unit (FIU) provides the interface between optical transmission equipment and the external optical fiber infrastructure.
The Optical Distribution Frame (ODF) provides an organized termination and distribution point for optical fibers.
Fiber pigtails and patch cords are essential for connecting optical equipment to the fiber distribution infrastructure.
The automatic allocation of two 30-meter pigtails is consistent with a predefined engineering configuration intended to accommodate optical connections between the FIU and ODF.
Option A is incorrect because the presence of fiber pigtails does not mean optical transceiver modules have been configured.
Option B is not justified merely because the device configuration contains fiber accessories without service boards. Optical cabling may be reserved independently of installed traffic-processing hardware.
Technical Conclusion: C is the intended answer. The uploaded training confirms the FIU/ODF connection-planning principle, but the precise default quantity of two 30-meter pigtails is not explicitly documented in the supplied slides.
Which of the following statements is incorrect?
The dispersion is in direct proportion to the fiber length.
The attenuation is in inverse proportion to the transmission distance.
The smaller the insertion loss, the better.
All of the above
Exact Extract — Huawei DC908 Solutions and Technologies Introduction, Page 94
“Real time data collection, analyze fiber attenuation”
Technical Deep Dive:
Optical transmission performance depends on several physical parameters, including attenuation, chromatic dispersion, polarization-mode dispersion, connector losses, and optical signal-to-noise ratio.
Option A — Correct.
For a uniform fiber with constant chromatic dispersion coefficient, accumulated chromatic dispersion increases proportionally with fiber length.
The accumulated dispersion can be calculated as:
D_total = D_λ × L
Where D_λ represents the fiber dispersion coefficient in ps/(nm·km), and L represents the fiber length in kilometers.
Option B — Incorrect.
Optical attenuation increases with transmission distance rather than decreasing inversely with it.
For a uniform fiber, total fiber attenuation is:
A_fiber = α × L
Where α is the attenuation coefficient in dB/km.
For example, if the attenuation coefficient is 0.2 dB/km, a 50 km fiber has approximately 10 dB of fiber attenuation, while a 100 km fiber has approximately 20 dB, excluding connector and splice losses.
Option C — Correct.
Lower insertion loss generally indicates better optical component transmission efficiency and leaves more margin in the optical power budget.
Option D — Incorrect as the intended selection.
Not all the preceding statements are incorrect.
Technical Conclusion: B is the correct answer because it reverses the relationship between fiber length and attenuation.
How many E9624 devices may be installed in a 19-inch cabinet?
2
3
1
4
Exact Extract — Huawei E9600 and E6600 Series Products and Industry Applications Introduction, Page 6
“Dimensions: 17 U high, 747.2 x 442 x 295 (H x W x D, unit: mm)”
The same hardware introduction identifies installation in a 19-inch cabinet.
Technical Deep Dive:
The Huawei OptiXtrans E9624 is a high-capacity optical-electrical integrated transmission platform designed for enterprise backbone and aggregation networks.
Its physical dimensions are approximately 747.2 mm in height, 442 mm in width, and 295 mm in depth.
The device occupies approximately 17 rack units (U).
A standard rack unit measures 44.45 mm. Therefore, a 17U E9624 requires approximately 755.65 mm of nominal rack-unit allocation.
Assuming a 42U 19-inch cabinet, the rack-unit calculation is:
42U ÷ 17U ≈ 2.47
Only complete devices can be installed, so the maximum based on available rack-unit height is two.
Two E9624 subracks occupy 34U, leaving approximately 8U for supporting installation requirements.
Three E9624 subracks would require 51U, exceeding the available 42U cabinet height.
During actual installation, engineers must also reserve appropriate space for the power distribution unit, cable routing, ventilation, and other supporting components.
Technical Conclusion: A is correct for the standard 42U cabinet arrangement used by the question. The 19-inch specification defines mounting width; cabinet height must also be specified to establish the absolute device count.
Which of the following boards does the OptiXtrans E6608T support?
Select All that Apply
AST2 board
Ponder board
OAU
TTA tributary board
Exact Extract — Network Planning, Design, Configuration and Quotation Guide, Page 70
“The OptiXtrans E6608T functions as the optical-layer chassis of the OptiXtrans E6616”
The same configuration rule specifies that only optical-layer and Ponder boards are supported in the described chassis role.
Technical Deep Dive:
The OptiXtrans E6608T is designed primarily for optical-layer transmission and wavelength-processing applications.
Its architecture differs from the E6608 and E6616 because it does not provide a centralized electrical cross-connect matrix.
The E6608T supports optical-layer functions and compatible optical transponder boards.
Option A — AST2 board (Correct):
AST2 provides optical supervisory channel and monitoring functionality. Supported AST2 implementations include embedded OTDR capabilities used for optical fiber supervision and fault localization.
Because AST2 is associated with optical-layer monitoring, it is consistent with the E6608T ' s supported optical board architecture.
Option B — Ponder board (Correct):
Ponder boards support optical transponder and muxponder functions. They enable client signals to be mapped or aggregated into higher-capacity optical wavelengths.
Option C — OAU (Correct):
The Optical Amplifier Unit provides optical amplification functions used to compensate for transmission attenuation and maintain adequate optical power levels.
Option D — TTA tributary board (Incorrect):
A TTA tributary board is an electrical-layer service-processing board. It is not supported in the E6608T optical-layer/Ponder-only configuration described in the training.
The distinction is important because equipment selected for optical wavelength transport cannot automatically be assumed to support electrical service grooming.
Technical Conclusion: A, B, and C are the intended selections.
Configuration qualification: Board compatibility must be checked against the exact chassis role and software release. The uploaded guide explicitly establishes the optical-layer/Ponder restriction for the described E6608T configuration, rather than documenting every possible standalone operating mode.
Which of the following media supports long-haul communication and provides the greatest transmission distance?
Multi-mode optical fiber
Twisted pair
Network cable
Cable
Single-mode optical fiber
Training Material Extract — Network Planning, Design, Configuration and Quotation Guide, Page 52
The network planning example identifies G.652 optical fiber for transmission spans and includes fiber distance, attenuation, and engineering margin as design parameters.
Technical Deep Dive:
Single-mode optical fiber is the preferred transmission medium for long-distance, high-capacity optical communication networks.
Its relatively small core, typically approximately 8–10 µm in diameter, supports propagation of the fundamental optical mode within its specified wavelength range.
This eliminates the intermodal dispersion that limits the transmission performance of multimode optical fiber.
Single-mode fiber is commonly operated within the 1310 nm and 1550 nm wavelength regions, where optical transmission characteristics are favorable.
At approximately 1550 nm, typical standard single-mode fiber attenuation is around 0.2 dB/km, although actual attenuation depends on the cable specification and installation.
Long-haul DWDM systems use single-mode fiber with coherent optical transceivers, optical amplifiers, wavelength multiplexing, and digital signal processing to transmit high-capacity services over hundreds or thousands of kilometers.
Multimode fiber is more suitable for relatively short-distance applications such as equipment-room and data-center connections.
Copper-based media, including twisted-pair Ethernet cables, have significantly shorter transmission distances without intermediate active equipment.
Technical Conclusion: E is correct because single-mode optical fiber provides the most suitable physical transmission characteristics for long-haul optical communications.
TESTED 20 Nov 2026
Copyright © 2014-2026 DumpsTool. All Rights Reserved