Winter Sale - Special Limited Time 65% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: dpt65

150-130 Questions and Answers

Question # 6

Which two features enable discovery of network switches? (Choose two.)

A.

LLDP

B.

UDLD

C.

FDP

D.

LFS

Full Access
Question # 7

Which two statements about LAGs are true? (Choose two.)

A.

A LAG provides load-sharing.

B.

A LAG provides sub-microsecond failover,

C.

A LAG can contain links of different speeds.

D.

A LAG is treated as a single logical link by the switch.

Full Access
Question # 8

Which two features are implemented using Brocade IronStack technology? (Choose two.)

A.

You can use any port on the switches to create your IronStack.

B.

You can mix devices running different software images in the same stack group.

C.

You can manage multiple physical switches in an IronStack as a single logical switch.

D.

You can perform a hitless stack failover without impacting Layer 2 and Layer 3 unicast traffic.

Full Access
Question # 9

When configuring an IP static route in a Brocade router, which three parameters are required?

(Choose three.)

A.

IP address of destination

B.

administrative distance for the route

C.

next hop

D.

subnet mask

E.

the metric for the route

Full Access
Question # 10

In which stage is an OSPF neighbor adjacency complete?

A.

loading

B.

exchange

C.

two-way

D.

full

Full Access
Question # 11

Which statement is true of an access control list (ACL) on a Brocade IP device?

A.

Only outbound ACLs can be used on any Brocade IP device.

B.

The ACL takes effect immediately after being applied to an interface.

C.

An ACL is immediately applied to all physical interfaces once the ACL is configured.

D.

Standard ACLs can be used to control traffic inbound or outbound based on source and destination addresses.

Full Access
Question # 12

You have configured your Brocade device as shown in the exhibit.

Brocade#sh ip

Switch IP address: 10.200.128.116

Subnet mask: 255.255.255.0

Default router address: 10.200.128.1

TFTP server address: 10.200.46.57

Configuration filename: Brocade

Image filename: None

IP MTU: 1500

Brocade#traceroute 10.200.128.1

Type Control-c to abort

Tracing the route to IP node 10.200.128.1 from 1 to 30 hops

1 <1 ms <1 ms <1 ms 10.200.128.1

Which statement is correct regarding interface Ethernet 10 on this device having inbound traffic from 172.17.1.1/24 to 172.17.2.1/24 on port 21?

A.

It would be permitted.

B.

It would be denied by the implicit deny statement.

C.

It would be denied by FTP port 21.

D.

This ACL only applies to outbound traffic.

Full Access
Question # 13

Which two multicast routing protocols are supported on Brocade FastIron devices? (Choose two.)

A.

DVMRP

B.

PIM

C.

MBGP

D.

MOSPF

Full Access
Question # 14

A workstation wants to send a packet to a destination that is not on the same network. Which destination MAC address will the workstation use to send the packet?

A.

destination MAC address

B.

gateway's MAC address

C.

multicast address

D.

broadcast address

Full Access
Question # 15

A powered device connected to a Brocade FastIron device has been auto discovered and classified as a class-3 PoE device. However, its power consumption is only 10 watts. Which command would be used on the FastIron to reallocate power back to the available power budget, while still providing all the necessary power to the powered device?

A.

no legacy-inline-power

B.

inline power power-by-class 2

C.

inline power priority 2

D.

inline power power-limit 11000

Full Access
Question # 16

Which two statements about ICL links in Brocade Multi-Chassis Trunk (MCT) implementations are true? (Choose two.)

A.

ICL links connect the two MCT chassis and allows MCT clients to see both devices as a single device.

B.

ICL links connect the MCT client devices to the MCT logical chassis.

C.

ICL links are necessary for the two devices to form an MCT cluster.

D.

ICL links allow the MCT logical chassis to communicate with a non-MCT device.

Full Access